lexiara

ANNEX I

For the purposes of section 1.1 the following definitions shall apply: 1.1.1.1. A family means a group of vehicle types fuelled by LPG, NG/biomethane identified by a parent vehicle. 1.1.1.2. A parent vehicle means a vehicle that is selected to act as the vehicle on which the self adaptability of a fuelling system is going to be demonstrated, and to which the members of a family refer. It is possible to have more than one parent vehicle in a family. 1.1.1.3. A member of the family means a vehicle that shares the following essential characteristics with its parent: It is produced by the same vehicle manufacturer; It is subject to the same emission limits; If the gas fuelling system has a central metering for the whole engine, it has a certified power output between 0,7 and 1,15 times that of the engine of the parent vehicle; If the gas fuelling system has an individual metering per cylinder, it has a certified power output per cylinder between 0,7 and 1,15 times that of the engine of the parent vehicle; If fitted with a catalyst system, it has the same type of catalyst i.e. three-way, oxidation, de NOx; It has a gas fuelling system (including the pressure regulator) from the same system manufacturer and of the same type: induction, vapour injection (single point, multipoint), liquid injection (single point, multipoint); This gas fuelling system is controlled by an ECU of the same type and technical specification, containing the same software principles and control strategy. The vehicle may have a second ECU compared to the parent vehicle, provided that the ECU is only used to control the injectors, additional shut-off valves and the data acquisition from additional sensors. With regard to the requirements referred to in point (c) and (d), in the case where a demonstration shows two gas fuelled vehicles could be members of the same family with the exception of their certified power output, respectively P1 and P2 (P1 < P2), and both are tested as if they were parent vehicles, the family relation will be considered valid for any vehicle with a certified power output between 0,7 × P1 and 1,15 × P2. In case of vehicles fuelled by LPG, NG/biomethane EC type-approval is granted subject to the following requirements: 1.1.2.1. For the type-approval of a parent vehicle, the parent vehicle shall demonstrate its capability to adapt to any fuel composition that may occur across the market. In the case of LPG there are variations in C3/C4 composition. In the case of natural gas there are generally two types of fuel, high calorific fuel (H-gas) and low calorific fuel (L-gas), but with a significant spread within both ranges; they differ significantly in Wobbe index. These variations are reflected in the reference fuels. 1.1.2.2. The parent vehicle shall be tested in the type 1 test on the two extreme gas reference fuels set out in Annex IX. In the case of NG/biomethane, if the transition from one gas fuel to the other gas fuel is in practice aided through the use of a switch, this switch shall not be used during type-approval. 1.1.2.3. The vehicle is considered to conform if, with both reference fuels, the vehicle complies with the emission limits. 1.1.2.4. The ratio of emission results ‘r’ shall be determined for each pollutant as follows: Type of fuel | Reference fuels | Calculation of ‘r’ LPG | fuel A | fuel B NG/Biomethane | fuel G20 | fuel G25 1.1.3. For the type-approval of a mono fuel gas vehicle and bi fuel gas vehicles operating in gas mode as a member of the family, a type 1 test shall be performed with one gas reference fuel. This reference fuel may be either of the gas reference fuels. The vehicle is considered to comply if the following requirements are met: the vehicle complies with the definition of a family member as defined in section 1.1.1.3; if the test fuel is the reference fuel A for LPG or G20 for NG/Biomethane, the emission result for each pollutant shall be multiplied by the relevant factor ‘r’ calculated in section 1.1.2.4 if r > 1; if r < 1, no correction is needed; if the test fuel is the reference fuel B for LPG or G25 for NG/Biomethane, the emission result for each pollutant shall be divided by the relevant factor ‘r’ calculated in section 1.1.2.4 if r < 1; if r > 1, no correction is needed; on the manufacturer’s request the type 1 test may be performed on both reference fuels, so that no correction is needed; the vehicle shall comply with the emission limits valid for the relevant category for both measured and calculated emissions; if repeated tests are made on the same engine the results on reference fuel G20, or A, and those on reference fuel G25, or B, shall first be averaged; the ‘r’ factor shall then be calculated from these averaged results; during the type 1 test the vehicle shall only use petrol for a maximum of 60 seconds when operating in gas mode. 1.2.1. For the type-approval of a flex fuel ethanol or biodiesel vehicle, the vehicle manufacturer shall describe the capability of the vehicle to adapt to any mixture of petrol and ethanol fuel (up to an 85 % ethanol blend) or diesel and biodiesel that may occur across the market. 1.2.2. For flex fuel vehicles, the transition from one reference fuel to another between the tests shall take place without manual adjustment of the engine settings. 2.1.1. List of legislative acts referred to in Article 3(3): Legislative Act | Requirements The California Code of Regulations, Title 13, Sections 1961(a) and 1961(b)(1)(C)(1) applicable to 2001 and later model year vehicles, 1968.1, 1968.2, 1968.5, 1976 and 1975, published by Barclay’s Publishing | Type-approval must be granted under the California Code of Regulations applicable to the most recent model year of light-duty vehicle. 2.2.1. The inlet orifice of the petrol or ethanol tank shall be designed so that it prevents the tank from being filled from a fuel pump delivery nozzle that has an external diameter of 23,6 mm or greater. 2.2.2. Section 2.2.1 shall not apply to a vehicle for which both of the following conditions are satisfied: the vehicle is designed and constructed so that no device designed to control the emission of gaseous pollutants is adversely affected by leaded petrol, and the vehicle is conspicuously, legibly and indelibly marked with the symbol for unleaded petrol specified in ISO 2575:2004 in a position immediately visible to a person filling the fuel tank. Additional markings are permitted. 2.2.3. Provision shall be made to prevent excess evaporative emissions and fuel spillage caused by a missing fuel filler cap. This may be achieved by using one of the following: an automatically opening and closing, non-removable fuel filler cap, design features which avoid excess evaporative emissions in the case of a missing fuel filler cap, any other provision which has the same effect. Examples may include, but are not limited to, a tethered filler cap, a chained filler cap or one utilizing the same locking key for the filler cap as for the vehicle’s ignition. In this case the key shall be removable from the filler cap only in the locked condition. 2.3.1. Any vehicle with an emission control computer shall include features to prevent modification, except as authorised by the manufacturer. The manufacturer shall authorise modifications if these modifications are necessary for the diagnosis, servicing, inspection, retrofitting or repair of the vehicle. Any reprogrammable computer codes or operating parameters shall be resistant to tampering and use the provisions in ISO 15031-7; dated 15 March 2001 (SAE J2186 dated October 1996) provided that the security exchange is conducted using the protocols and diagnostic connector as prescribed in Appendix 1 to Annex XI. Any removable calibration memory chips shall be potted, encased in a sealed container or protected by electronic algorithms and shall not be changeable without the use of specialised tools and procedures. Only features directly associated with emissions calibration or prevention of vehicle theft may be so protected. 2.3.2. Computer-coded engine operating parameters shall not be changeable without the use of specialized tools and procedures (e. g. soldered or potted computer components or sealed (or soldered) computer enclosures). 2.3.3. In the case of mechanical fuel-injection pumps fitted to compression-ignition engines, manufacturers shall take adequate steps to protect the maximum fuel delivery setting from tampering while a vehicle is in service. 2.3.4. Manufacturers may apply to the approval authority for an exemption to one of the requirements of Section 2.3 for those vehicles which are unlikely to require protection. The criteria that the approval authority shall evaluate in considering an exemption shall include the current availability of performance chips, the high-performance capability of the vehicle and the projected sales volume of the vehicle. 2.3.5. Manufacturers using programmable computer code systems (e.g. electrical erasable programmable read-only memory, EEPROM) shall deter unauthorised reprogramming. Manufacturers shall include enhanced tamper-protection strategies and write-protect features requiring electronic access to an off-site computer maintained by the manufacturer ’, to which independent operators shall also have access using the protection afforded in Section 2.3.1. and Section 2.2. of Annex XIV. Methods giving an adequate level of tamper protection shall be approved by the approval authority. 2.4.1. Figure I.2.4 illustrates the application of the tests for type-approval of a vehicle. The specific test procedures are described in Annexes II, III, IV, V, VI, VII, VIII, X, XI, XII and XVI (1). Figure I.2.4 Application of test requirements for type-approval and extensions Vehicle category | Vehicles with positive ignition engines including hybrids | Vehicles with compression ignition engines including hybrids Mono fuel | Bi fuel (2) | Flex fuel (2) | Flex fuel | Mono fuel Reference fuel | Petrol (E5) | LPG | NG/Biomethane | Hydrogen | Petrol (E5) | Petrol (E5) | Petrol (E5) | Petrol (E5) | Diesel (B5) | Diesel (B5) LPG | NG/Biomethane | Hydrogen | Ethanol (E85) | Biodiesel Gaseous pollutants (Type 1 test) | Yes | Yes | Yes | | Yes (both fuels) | Yes (both fuels) | | Yes (both fuels) | | Yes Particulates (Type 1 test) | Yes (direct injection) | — | — | | Yes (direct injection) (petrol) | Yes (direct injection) (petrol) | | Yes (direct injection) (both fuels) | | Yes Idle emissions (Type 2 test) | Yes | Yes | Yes | | Yes (both fuels) | Yes (both fuels) | | Yes (both fuels) | | — Crankcase emissions (Type 3 test) | Yes | Yes | Yes | | Yes (petrol) | Yes (petrol) | | Yes (petrol) | | — Evaporative emissions (Type 4 test) | Yes | — | — | | Yes (petrol) | Yes (petrol) | | Yes (petrol) | | — Durability (Type 5 test) | Yes | Yes | Yes | | Yes (petrol) | Yes (petrol) | | Yes (petrol) | | Yes Low temperature emissions (Type 6 test) | Yes | — | — | | Yes (petrol) | Yes (petrol) | | Yes (3) (both fuels) | | In-service conformity | Yes | Yes | Yes | | Yes (both fuels) | Yes (both fuels) | | Yes (both fuels) | | Yes On-board diagnostics | Yes | Yes | Yes | | Yes | Yes | | Yes | | Yes CO2 emissions and fuel consumption | Yes | Yes | Yes | | Yes (both fuels) | Yes (both fuels) | | Yes (both fuels) | | Yes Smoke opacity | — | — | — | | — | — | | — | | Yes Vehicles with different reference masses 3.1.1.1. The type-approval shall be extended only to vehicles with a reference mass requiring the use of the next two higher equivalent inertia or any lower equivalent inertia. 3.1.1.2. For category N vehicles, the approval shall be extended only to vehicles with a lower reference mass, if the emissions of the vehicle already approved are within the limits prescribed for the vehicle for which extension of the approval is requested. Vehicles with different overall transmission ratios 3.1.2.1. The type-approval shall be extended to vehicles with different transmission ratios only under certain conditions. 3.1.2.2. To determine whether type-approval can be extended, for each of the transmission ratios used in the type 1 and type 6 tests, the proportion, shall be determined where, at an engine speed of 1 000 rpm, V1 is the speed of the vehicle-type approved and V2 is the speed of the vehicle type for which extension of the approval is requested. 3.1.2.3. If, for each transmission ratio, E ≤ 8 %, the extension shall be granted without repeating the type 1 and type 6 tests. 3.1.2.4. If, for at least one transmission ratio, E > 8 %, and if, for each gear ratio, E ≤ 13 %, the type 1 and type 6 tests shall be repeated. The tests may be performed in a laboratory chosen by the manufacturer subject to the approval of the technical service. The report of the tests shall be sent to the technical service responsible for the type-approval tests. 3.1.3. Vehicles with different reference masses and transmission ratios The type-approval shall be extended to vehicles with different reference masses and transmission ratios, provided that all the conditions prescribed in 3.1.1 and 3.1.2 are fulfilled. Vehicles with periodically regenerating systems The type-approval of a vehicle type equipped with a periodically regenerating system shall be extended to other vehicles with periodically regenerating systems, whose parameters described below are identical, or within the stated tolerances. The extension shall only relate to measurements specific to the defined periodically regenerating system. 3.1.4.1. Identical parameters for extending approval are: Engine, Combustion process, Periodically regenerating system (i.e. catalyst, particulate trap), Construction (i.e. type of enclosure, type of precious metal, type of substrate, cell density), Type and working principle, Dosage and additive system, Volume ±10 per cent, Location (temperature ±50 °C at 120 km/h or 5 per cent difference of max. temperature/pressure). 3.1.4.2. Use of Ki factors for vehicles with different reference masses The Ki factors developed by the procedures in section 3 of Annex 13 of UN/ECE Regulation No 83 for type-approval of a vehicle type with a periodically regenerating system, may be used by other vehicles which meet the criteria referred to in section 3.1.4.1 and have a reference mass within the next two higher equivalent inertia classes or any lower equivalent inertia. 3.1.5. Application of extensions to other vehicles When an extension has been granted in accordance with 3.1.1 to 3.1.4, such a type-approval shall not be further extended to other vehicles. The type-approval shall be extended to vehicles equipped with a control system for evaporative emissions which meet the following conditions: 3.2.1.1. The basic principle of fuel/air metering (e.g. single point injection) is the same. 3.2.1.2. The shape of the fuel tank and the material of the fuel tank and liquid fuel hoses is identical. 3.2.1.3. The worst-case vehicle with regard to the cross-section and approximate hose length shall be tested. Whether non-identical vapour/liquid separators are acceptable is decided by the technical service responsible for the type-approval tests. 3.2.1.4. The fuel tank volume is within a range of ±10 %. 3.2.1.5. The setting of the fuel tank relief valve is identical. 3.2.1.6. The method of storage of the fuel vapour is identical, i.e. trap form and volume, storage medium, air cleaner (if used for evaporative emission control), etc. 3.2.1.7. The method of purging of the stored vapour is identical (e.g. air flow, start point or purge volume over the preconditioning cycle). 3.2.1.8. The method of sealing and venting of the fuel metering system is identical. The type-approval shall be extended to vehicles with: 3.2.2.1. different engine sizes; 3.2.2.2. different engine powers; 3.2.2.3. automatic and manual gearboxes; 3.2.2.4. two and four wheel transmissions; 3.2.2.5. different body styles; and 3.2.2.6. different wheel and tyre sizes. The type-approval shall be extended to different vehicle types, provided that the vehicle, engine or pollution control system parameters specified below are identical or remain within the prescribed tolerances: 3.3.1.1. Vehicle: Inertia category: the two inertia categories immediately above and any inertia category below. Total road load at 80 km/h: +5 % above and any value below. 3.3.1.2. Engine engine cylinder capacity (±15 %), number and control of valves, fuel system, type of cooling system, combustion process. 3.3.1.3. Pollution control system parameters: Catalytic converters and particulate filters: number of catalytic converters, filters and elements, size of catalytic converters and filters (volume of monolith ±10 %), type of catalytic activity (oxidizing, three-way, lean NOx trap, SCR, lean NOx catalyst or other), precious metal load (identical or higher), precious metal type and ratio (±15 %), substrate (structure and material), cell density, temperature variation of no more than 50 K at the inlet of the catalytic converter or filter. This temperature variation shall be checked under stabilized conditions at a speed of 120 km/h and the load setting of the type 1 test. Air injection: with or without type (pulsair, air pumps, other(s)) EGR: with or without type (cooled or non cooled, active or passive control, high pressure or low pressure). 3.3.1.4. The durability test may be carried out using a vehicle, which has a different body style, gear box (automatic or manual) and size of the wheels or tyres, from those of the vehicle type for which the type-approval is sought. 3.4.1. The type-approval shall be extended to different vehicles with identical engine and emission control systems as defined in Annex XI, Appendix 2. The type-approval shall be extended regardless of the following vehicle characteristics: engine accessories; tyres; equivalent inertia; cooling system; overall gear ratio; transmission type; and type of bodywork. Vehicles powered by an internal combustion engine only, except vehicles equipped with a periodically regenerating emission control system. 3.5.1.1. The type-approval shall be extended to vehicles differing with regard to the following characteristics, if the CO2 emissions measured by the technical service do not exceed the type-approval value by more than 4 % for vehicles of category M and 6 % for vehicles of category N: reference mass, technically permissible maximum laden mass, type of bodywork as defined in Section C of Annex II of Directive 2007/46/EC, overall gear ratios, engine equipment and accessories., Vehicles powered by an internal combustion engine only and equipped with a periodically regenerating emission control system 3.5.2.1. The type-approval shall be extended to vehicles, differing with regard to the characteristics given in Section 3.5.1.1 above, but not exceeding the family characteristics of UN/ECE Regulation No 101 (4), Annex 10, if the CO2 emissions measured by the technical service do not exceed the type approved value by more than 4 % for vehicles of category M and 6 % for vehicles of category N, and where the same Ki factor is applicable. 3.5.2.2. The type-approval shall be extended to vehicles with a different Ki factor, if the CO2 emissions measured by the technical service do not exceed the type approved value by more than 4 % for vehicles of category M and 6 % for vehicles of category N. 3.5.3. Vehicles powered by an electric power train only Extensions shall be granted after agreement with the technical service responsible for conducting the tests. 3.5.4. Vehicles powered by a hybrid electric power train The type-approval shall be extended to vehicles differing with regard to the following characteristics, if the CO2 emissions and the electric energy consumption measured by the technical service do not exceed the type approved value by more than 4 % for vehicles of category M and 6 % for vehicles of category N: reference mass, technically permissible maximum laden mass, Type of bodywork as defined in Section C of Annex II of Directive 2007/46/EC, With respect to a change in any other characteristic extensions may be granted after agreement with the technical service responsible for conducting the tests., Extension of type-approval of vehicles of category N within a family: 3.5.5.1. For vehicles of category N that are approved as members of a vehicle family using the procedure in Section 3.6.2, the type-approval shall be extended to vehicles from within the same family only if the technical service estimates that the fuel consumption of the new vehicle does not exceed the fuel consumption of the vehicle on which the family’s fuel consumption is based. Type-approvals may also be extended to vehicles which: are up to 110 kg heavier than the family member tested, provided that they are within 220 kg of the lightest member of the family, have a lower overall transmission ratio than the family member tested due solely to a change in tyre sizes, and, conform with the family in all other respects., 3.5.5.2. For vehicles of category N that are type-approved as members of a vehicle family using the procedure in point 3.6.3, the type-approval can be extended to vehicles from within the same family without additional testing only if the technical service estimates that the fuel consumption of the new vehicle falls within the limits made up of those two vehicles in the family that have the lowest and the highest fuel consumption, respectively. Vehicles of category N shall be type-approved within a family as defined in point 3.6.1 using one of the two alternative methods described in points 3.6.2 and 3.6.3. N vehicles may be grouped together into a family for the purposes of measurement of fuel consumption and CO2 emissions if the following parameters are identical or within the specified limits: 3.6.1.1. Identical parameters shall be the following: manufacturer and type as defined in section I of Appendix 4, engine capacity, emission control system type, fuel system type as defined in point 1.10.2 of Appendix 4., 3.6.1.2. The following parameters shall be within the following limits: transmission overall ratios (no more than 8 % higher than the lowest) as defined in point 1.13.3 of Appendix 4, reference mass (no more than 220 kg lighter than the heaviest), frontal area (no more than 15 % smaller than the largest), engine power (no more than 10 % less than the highest value). 3.6.2. A vehicle family, as defined in point 3.6.1, may be approved with CO2 emission and fuel consumption data that are common to all members of the family. The technical service shall select for testing the member of the family which the service considers to have the highest CO2 emission. The measurements shall be performed as described in Annex XII, and the results according to the method described in section 5.5 of UN/ECE Regulation No 101 shall be used as type-approval values that are common to all members of the family. 3.6.3. Vehicles that are grouped in a family as defined in point 3.6.1 may be approved with individual CO2 emission and fuel consumption data for each of the family members. The technical service shall select for testing the two vehicles, which the service considers to have the highest and the lowest CO2 emissions respectively. The measurements shall be performed as described in Annex XII. If the manufacturer’s data for these two vehicles falls within the tolerance limits described in section 5.5 of UN/ECE Regulation No 101, the CO2 emissions declared by the manufacturer for all members of the vehicle family can be used as type-approval values. If the manufacturer’s data do not fall within the tolerance limits, the results according to the method described in section 5.5 of UN/ECE Regulation No 101 shall be used as type-approval values and the technical service shall select an appropriate number of other family members for additional tests. 4.1.1. Where applicable the tests of types 1, 2, 3, 4, the test for OBD, the test for CO2 emissions and fuel consumption and the test for smoke opacity shall be performed, as described in section 2.4. The specific procedures for conformity of production are set out in the sections 4.2 to 4.10. 4.2.1. The type 1 test shall be carried out on a vehicle of the same specification as described in the type-approval certificate. When a type 1 test is to be carried out for a vehicle type-approval that has one or several extensions, the type 1 tests shall be carried out either on the vehicle described in the initial information package or on the vehicle described in the information package relating to the relevant extension. After selection by the approval authority, the manufacturer shall not undertake any adjustment to the vehicles selected. 4.2.2.1. Three vehicles shall be selected at random in the series and tested as described in Annex III to this Regulation. The deterioration factors shall be used in the same way. The limit values are set out in Tables 1 and 2 of Annex I to Regulation (EC) No 715/2007. 4.2.2.2. If the approval authority is satisfied with the production standard deviation given by the manufacturer in accordance with Annex X to Directive 2007/46/EC, the tests shall be carried out according to Appendix 1 of this Annex. If the approval authority is not satisfied with the production standard deviation given by the manufacturer in accordance with Annex X to Directive 2007/46/EC, the tests shall be carried out according to Appendix 2 of this Annex. The production of a series shall be deemed to conform or not to conform on the basis of a sampling test of the vehicles once a pass decision is reached for all the pollutants or a fail decision is reached for one pollutant, according to the test criteria applied in the appropriate appendix. When a pass decision has been reached for one pollutant, that decision shall not be changed by any additional tests carried out to reach a decision for the other pollutants. If no pass decision is reached for all the pollutants and no fail decision is reached for one pollutant, a test shall be carried out on another vehicle (see Figure I.4.2). Test of three vehicles Computation of the test statistic According to the appropriate Appendix does the test statistic agree with the criteria for failing the series for at least one pollutant? YES Series rejected NO NO According to the appropriate Appendix does the test statistic agree with the criteria for passing the series for at least one pollutant? YES A pass decision is reached for one or more pollutants Is a pass decision reached for all the pollutants? YES Series accepted NO Test of an additional vehicle Notwithstanding the requirements of Annex III, the tests shall be carried out on vehicles coming straight off the production line. 4.2.3.1. However, at the request of the manufacturer, the tests may be carried out on vehicles which have completed: A maximum of 3 000 km for vehicles equipped with a positive ignition engine; A maximum of 15 000 km for vehicles equipped with a compression ignition engine. The running-in procedure shall be conducted by the manufacturer, who shall undertake not to make any adjustments to these vehicles. 4.2.3.2. If the manufacturer wishes to run in the vehicles, (‘x’ km, where x ≤ 3 000 km for vehicles equipped with a positive ignition engine and x ≤ 15 000 km for vehicles equipped with a compression ignition engine), the procedure shall be the following: the pollutant emissions (type 1) shall be measured at zero and at ‘x’ km on the first tested vehicle; the evolution coefficient of the emissions between zero and ‘x’ km shall be calculated for each of the pollutant: Emissions ‘x’ km/Emissions zero km This may be less than 1; and the other vehicles shall not be run in, but their zero km emissions shall be multiplied by the evolution coefficient. In this case, the values to be taken shall be: the values at ‘x’ km for the first vehicle; the values at zero km multiplied by the evolution coefficient for the other vehicles. 4.2.3.3. All these tests shall be conducted with commercial fuel. However, at the manufacturer’s request, the reference fuels described in Annex IX may be used. 4.3.1. If a vehicle type has had one or several extensions, the tests shall be carried out on the vehicle(s) described in the information package which accompanied the first type-approval application, or on the vehicle described in the information package that accompanied the relevant extension. 4.3.2. If the approval authority is not satisfied with the auditing procedure of the manufacturer, points 3.3 and 3,4 of Annex X to Directive 2007/46/EC shall apply. 4.3.3. For the purpose of this section and Appendices 1 and 2, the term ‘pollutant’ shall include the regulated pollutants (given in Tables 1 and 2 of Annex I to Regulation (EC) No 715/2007) and the emission of CO2. The conformity of the vehicle for CO2 emissions shall be determined in accordance with the procedure described in point 4.2.2. with the following exceptions: 4.3.4.1. The provisions of Section 4.2.2.1 shall be replaced by the following: Three vehicles shall be randomly taken in the series and tested as described in Annex XII. 4.3.4.2. The provisions of Section 4.2.3.1 shall be replaced by the following: However, at the request of the manufacturer, the tests may be carried out on vehicles which have completed a maximum of 15 000 km. In this case, the running-in procedure shall be conducted by the manufacturer, who shall undertake not to make any adjustments to these vehicles. 4.3.4.3. The provisions of Section 4.2.3.2 shall be replaced by the following: If the manufacturer wishes to run in the vehicles, (‘x’ km, where x ≤ 15 000 km), the procedure shall be the following: the pollutant emissions shall be measured at zero and at ‘x’ km on the first tested vehicle; the evolution coefficient of the emissions between zero and ‘x’ km shall be calculated for each of the pollutant: Emissions ‘x’ km/Emissions zero km This may be less than 1; and the other vehicles shall not be run in, but their zero km emissions shall be multiplied by the evolution coefficient. In this case, the values to be taken shall be: the values at ‘x’ km for the first vehicle; the values at zero km multiplied by the evolution coefficient for the other vehicles. 4.3.4.4. The provisions of Section 4.2.3.3 shall be replaced by the following: The reference fuels described in Annex IX of this Regulation, shall be used for testing. 4.3.4.5. When checking the conformity of vehicle for CO2 emissions, as an alternative to the procedure mentioned in Section 4.3.4.3, the vehicle manufacturer may use a fixed evolution coefficient EC of 0,92 and multiply all values of CO2 measured at zero km by this factor. Measures to ensure the conformity of production with regard to electric energy consumption shall be checked on the basis of the description in the type-approval certificate set out in Appendix 4 to this Annex. The holder of the approval shall, in particular: 4.4.1.1. Ensure the existence of procedures for the effective control of production quality; 4.4.1.2. Have access to the equipment necessary for checking conformity with each approved type; 4.4.1.3. Ensure that the data concerning the test result are recorded and that the annexed documents are available during a period to be agreed with the administrative service; 4.4.1.4. Analyse the results of each type of test so as to monitor and ensure the consistency of the characteristics of the product, taking into account the variations admissible in industrial manufacture; 4.4.1.5. Make sure that for each type of vehicle tests referred to in Annex XII to this Regulation are carried out; notwithstanding the requirements of paragraph 2.3.1.6 of Annex 7 of UN/ECE Regulation No 101, at the request of the manufacturer, the tests shall be carried out on vehicles which have not travelled any distance; 4.4.1.6. Make sure that any collections of samples or test pieces demonstrating non-conformity with the type test under consideration is followed by a subsequent sampling and a further test. All necessary steps shall be taken to re-establish the conformity of production. The approval authorities may verify at any time the methods applied in each production unit. 4.4.2.1. In every inspection, the records of tests and production monitoring shall be communicated to the visiting inspector. 4.4.2.2. The inspector may select at random the samples to be tested in the manufacturer’s laboratory. The minimum number of samples shall be determined on the basis of the results of the manufacturer’s own checks. 4.4.2.3. When the quality standard does not seem satisfactory or when it seems necessary to verify the validity of the tests conducted under Section 4.4.2.2, the inspector shall collect samples to be sent to the technical service which carried out the approval tests. 4.4.2.4. The approval authorities may carry out all the tests set out in this Regulation. 4.5.1. Measures to ensure the conformity of production with regard to CO2 emissions and electric energy consumption from hybrid electric vehicles shall be checked on the basis of the description in the type-approval certificate conforming to the model in Appendix 4. 4.5.2. The control of production conformity shall be based on an assessment made by the approval authority of the manufacturer’s auditing procedure in order to ensure conformity of the vehicle type with respect to the emission of CO2 and the electric energy consumption. 4.5.3. If the approval authority is not satisfied with the standard of the manufacturer’s auditing procedure, it shall require that verification tests be carried out on vehicles in production. 4.5.4. Conformity for CO2 emissions shall be checked using the statistical procedures described in Section 4.3 and Appendices 1 and 2. Vehicles shall be tested according to the procedure referred to in Annex XII. 4.6.1. If a type 3 test is to be carried out, it shall be conducted on all vehicles selected for the type 1 conformity of production test set out in section 4.2. The conditions laid down in Annex V shall apply. 4.7.1. If a type 4 test is to be carried out, it shall be conducted in accordance with Annex VI. If a verification of the performance of the OBD system is to be carried out, it shall be conducted in accordance with the following requirements: 4.8.1.1. When the approval authority determines that the quality of production seems unsatisfactory, a vehicle shall be randomly taken from the series and subjected to the tests described in Appendix 1 to Annex XI. 4.8.1.2. The production shall be deemed to conform if this vehicle meets the requirements of the tests described in Appendix 1 to Annex XI. 4.8.1.3. If the vehicle taken from the series does not satisfy the requirements of section 4.8.1.1, a further random sample of four vehicles shall be taken from the series and subjected to the tests described in Appendix 1 to Annex XI. The tests may be carried out on vehicles which have been run in for no more than 15 000 km. 4.8.1.4. The production shall be deemed to conform if at least 3 vehicles meet the requirements of the tests described in Annex XI, Appendix 1. 4.9.1. Tests for conformity of production may be performed with a commercial fuel of which the C3/C4 ratio lies between those of the reference fuels in the case of LPG, or of which the Wobbe index lies between those of the extreme reference fuels in the case of NG. In that case a fuel analysis shall be presented to the approval authority. 4.10.1. Conformity of the vehicle with the approved type as regards the emission of pollutants from compression ignition engines shall be verified on the basis of the results listed in the Addendum to the type-approval certificate set out in point 2.4 of Appendix 4. 4.10.2. In addition to point 10.1, where a check is carried out on a vehicle taken from the series, the tests shall be carried out as follows: 4.10.2.1 A vehicle which has not been run in shall be subjected to the test under free acceleration described in section 4.3 of Appendix 2 to Annex IV. The vehicle shall be deemed to conform to the approved type if the absorption coefficient determined does not exceed by more than 0·5 m–1 the figure shown in the approval mark. 4.10.2.2 If the figure determined in the test referred to in point 4.10.2.1. exceeds by more than 0·5 m–1 the figure shown in the approval mark, a vehicle of the type considered or its engine shall be subjected to the test at steady speeds over the full-load curve, as described in section 4.2 of Appendix 2 to Annex IV. The emission levels shall not exceed the limits prescribed in Annex 7 to UN/ECE Regulation No 24 (5).

· All articles ·

Source: EUR-Lex (Cellar) · retrieved 2026-11-20 · Text as adopted (Official Journal); later amendments are not incorporated in this text.