ANNEX IX
Type: Petrol (E5) Parameter | Unit | Limits (1) | Test method Minimum | Maximum Research octane number, RON | | 95,0 | — | EN 25164 prEN ISO 5164 Motor octane number, MON | | 85,0 | — | EN 25163 prEN ISO 5163 Density at 15 °C | kg/m3 | 743 | 756 | EN ISO 3675 EN ISO 12185 Vapour pressure | kPa | 56,0 | 60,0 | EN ISO 13016-1 (DVPE) Water content | % v/v | | 0,015 | ASTM E 1064 Distillation: | | | | — Evaporated at 70 °C, | % v/v | 24,0 | 44,0 | EN-ISO 3405 — evaporated at 100 °C, | % v/v | 48,0 | 60,0 | EN-ISO 3405 — evaporated at150 °C, | % v/v | 82,0 | 90,0 | EN-ISO 3405 — final boiling point, | °C | 190 | 210 | EN-ISO 3405 Residue | % v/v | — | 2,0 | EN-ISO 3405 Hydrocarbon analysis: | | | | — olefins, | % v/v | 3,0 | 13,0 | ASTM D 1319 — aromatics, | % v/v | 29,0 | 35,0 | ASTM D 1319 — benzene, | % v/v | — | 1,0 | EN 12177 — saturates, | % v/v | Report | ASTM 1319 Carbon/hydrogen ratio | | Report | Carbon/oxygen ratio | | Report | Induction period (2) | minutes | 480 | — | EN-ISO 7536 Oxygen content (3) | % m/m | Report | EN 1601 Existent gum | mg/ml | — | 0,04 | EN-ISO 6246 Sulphur content (4) | mg/kg | — | 10 | EN ISO 20846 EN ISO 20884 Copper corrosion | | — | Class 1 | EN-ISO 2160 Lead content | mg/l | — | 5 | EN 237 Phosphorus content (5) | mg/l | — | 1,3 | ASTM D 3231 Ethanol (3) | % v/v | 4,7 | 5,3 | EN 1601 EN 13132 Type: Ethanol (E85) Parameter | Unit | Limits (6) | Test method (7) Minimum | Maximum Research octane number, RON | | 95 | — | EN ISO 5164 Motor octane number, MON | | 85 | — | EN ISO 5163 Density at 15 °C | kg/m3 | Report | ISO 3675 Vapour pressure | kPa | 40 | 60 | EN ISO 13016-1 (DVPE) Sulphur content (8) (9) | mg/kg | — | 10 | EN ISO 20846 EN ISO 20884 Oxidation stability | minutes | 360 | | EN ISO 7536 Existent gum content (solvent washed) | mg/100ml | — | 5 | EN-ISO 6246 Appearance This shall be determined at ambient temperature or 15 °C whichever is higher. | | Clear and bright, visibly free of suspended or precipitated contaminants | Visual inspection Ethanol and higher alcohols (12) | % (V/V) | 83 | 85 | EN 1601 EN 13132 EN 14517 Higher alcohols (C3-C8) | % (V/V) | — | 2 | Methanol | % (V/V) | | 0,5 | Petrol (10) | % (V/V) | Balance | EN 228 Phosphorus | mg/l | 0,3 (11) | ASTM D 3231 Water content | % (V/V) | | 0,3 | ASTM E 1064 Inorganic chloride content | mg/l | | 1 | ISO 6227 pHe | | 6,5 | 9 | ASTM D 6423 Copper strip corrosion (3h at 50 °C) | Rating | Class 1 | | EN ISO 2160 Acidity, (as acetic acid CH3COOH) | % (m/m) (mg/l) | — | 0,005-40 | ASTM D 1613 Carbon/hydrogen ratio | | report | Carbon/oxygen ration | | report | Type: LPG Parameter | Unit | Fuel A | Fuel B | Test method Composition: | | | | ISO 7941 C3-content | % vol | 30 ± 2 | 85 ± 2 | C4-content | % vol | Balance | Balance | < C3, > C4 | % vol | Maximum 2 | Maximum 2 | Olefins | % vol | Maximum 12 | Maximum 15 | Evaporation residue | mg/kg | Maximum 50 | Maximum 50 | prEN 15470 Water at 0 °C | | Free | Free | prEN 15469 Total sulphur content | mg/kg | Maximum 10 | Maximum 10 | ASTM 6667 Hydrogen sulphide | | None | None | ISO 8819 Copper strip corrosion | Rating | Class 1 | Class 1 | ISO 6251 (13) Odour | | Characteristic | Characteristic | Motor octane number | | Minimum 89 | Minimum 89 | EN 589 Annex B Type: NG/Biomethane Characteristics | Units | Basis | Limits | Test method minimum | maximum Reference fuel G20 Composition: | | | | | Methane | % mole | 100 | 99 | 100 | ISO 6974 Balance (14) | % mole | — | — | 1 | ISO 6974 N2 | % mole | | | | ISO 6974 Sulphur content | mg/m3 (15) | — | — | 10 | ISO 6326-5 Wobbe Index (net) | MJ/m3 (16) | 48,2 | 47,2 | 49,2 | Reference fuel G25 Composition: | | | | | Methane | % mole | 86 | 84 | 88 | ISO 6974 Balance (14) | % mole | — | — | 1 | ISO 6974 N2 | % mole | 14 | 12 | 16 | ISO 6974 Sulphur content | mg/m3 (15) | — | — | 10 | ISO 6326-5 Wobbe Index (net) | MJ/m3 (16) | 39,4 | 38,2 | 40,6 | Type: Diesel (B5) Parameter | Unit | Limits (17) | Test method Minimum | Maximum Cetane number (18) | | 52,0 | 54,0 | EN-ISO 5165 Density at 15 °C | kg/m3 | 833 | 837 | EN-ISO 3675 Distillation: | | | | — 50 % point | °C | 245 | — | EN-ISO 3405 — 95 % point | °C | 345 | 350 | EN-ISO 3405 — final boiling point | °C | — | 370 | EN-ISO 3405 Flash point | °C | 55 | — | EN 22719 CFPP | °C | — | –5 | EN 116 Viscosity at 40 °C | mm2/s | 2,3 | 3,3 | EN-ISO 3104 Polycyclic aromatic hydrocarbons | % m/m | 2,0 | 6,0 | EN 12916 Sulphur content (19) | mg/kg | — | 10 | EN ISO 20846/EN ISO 20884 Copper corrosion | | — | Class 1 | EN-ISO 2160 Conradson carbon residue (10 % DR) | % m/m | — | 0,2 | EN-ISO10370 Ash content | % m/m | — | 0,01 | EN-ISO 6245 Water content | % m/m | — | 0,02 | EN-ISO12937 Neutralisation (strong acid) number | mg KOH/g | — | 0,02 | ASTM D 974 Oxidation stability (20) | mg/ml | — | 0,025 | EN-ISO12205 Lubricity (HFRR wear scan diameter at 60 °C) | µm | — | 400 | EN ISO 12156 Oxidation stability at 110 °C (20) (22) | h | 20,0 | | EN 14112 FAME (21) | % v/v | 4,5 | 5,5 | EN 14078 Type: Petrol (E5) Parameter | Unit | Limits (23) | Test method Minimum | Maximum Research octane number, RON | | 95,0 | — | EN 25164 prEN ISO 5164 Motor octane number, MON | | 85,0 | — | EN 25163 prEN ISO 5163 Density at 15 °C | kg/m3 | 743 | 756 | ISO 3675 EN ISO 12185 Vapour pressure | kPa | 56,0 | 95,0 | EN ISO 13016-1 (DVPE) Water content | % v/v | | 0,015 | ASTM E 1064 Distillation: | | | | — evaporated at 70 °C | % v/v | 24,0 | 44,0 | EN-ISO 3405 — evaporated at 100 °C | % v/v | 50,0 | 60,0 | EN-ISO 3405 — evaporated at 150 °C | % v/v | 82,0 | 90,0 | EN-ISO 3405 — final boiling point | °C | 190 | 210 | EN-ISO 3405 Residue | % v/v | — | 2,0 | EN-ISO 3405 Hydrocarbon analysis: | | | | — olefins | % v/v | 3,0 | 13,0 | ASTM D 1319 — aromatics | % v/v | 29,0 | 35,0 | ASTM D 1319 — benzene | % v/v | — | 1,0 | EN 12177 — saturates | % v/v | Report | ASTM D 1319 Carbon/hydrogen ratio | | Report | Carbon/oxygen ratio | | Report | Induction period (24) | minutes | 480 | — | EN-ISO 7536 Oxygen content (25) | % m/m | Report | EN 1601 Existent gum | mg/ml | — | 0,04 | EN-ISO 6246 Sulphur content (26) | mg/kg | — | 10 | EN ISO 20846 EN ISO 20884 Copper corrosion | | — | Class 1 | EN-ISO 2160 Lead content | mg/l | — | 5 | EN 237 Phosphorus content (27) | mg/l | — | 1,3 | ASTM D 3231 Ethanol (25) | % v/v | 4,7 | 5,3 | EN 1601 EN 13132 Type: Ethanol (E75) Reference fuel specification to be developed in advance of the dates set out in Article 10(6) of Regulation (EC) No 715/2007.
← anx_VIII__para__9 · All articles · SPECIFICATIONS OF REFERENCE FUELS →
Source: EUR-Lex (Cellar) · retrieved 2026-11-20 · Text as adopted (Official Journal); later amendments are not incorporated in this text.