ANNEX XII
This Annex sets out the requirements for the measurement of CO2 emissions and fuel consumption. 2.1. The general specifications for conducting the tests and interpreting the results shall be those set out in Section 5 of UN/ECE Regulation 101 with the exceptions specified below. Test fuel 2.2.1. The appropriate reference fuels as defined in Annex IX of this Regulation shall be used for testing. 2.2.2. For LPG and NG, that fuel shall be used which is chosen by the manufacturer for the measurement of the net power in accordance with Annex I to Council Directive 80/1269/EEC (1). The chosen fuel shall be specified in the information document as defined in Appendix 3 to Annex I of this Regulation. 2.3. Paragraph 5.2.4. of UN/ECE Regulation 101 shall read: density: measured on the test fuel according to ISO 3675 or an equivalent method. For petrol, diesel, biodiesel and ethanol (E85) the density measured at 15 °C will be used; for LPG and natural gas/biomethane a reference density will be used, as follows: | 0,538 kg/litre for LPG | 0,654 kg/m3 for NG hydrogen-carbon-oxygen ratio:fixed values will be used which are: | C1H1,89O0,016 for petrol, | C1H1,86O0,005 for diesel, | C1H2,525 for LPG (liquefied petroleum gas), | CH4 for NG (natural gas) and biomethane, | C1H2,74O0,385 for ethanol (E85). 3.1. The technical requirements and specifications for the measurement of CO2 emissions, fuel consumption or electric energy consumption shall be those set out in Annexes 6 to 10 to UN/ECE Regulation 101 with the exceptions specified below. 3.2. In Annex 6, section 1.3.5 of UN/ECE Regulation 101 the tyres used shall meet the same selection criteria as those specified for the type 1 emissions test, set out in Annex III section 3.5 of this Regulation. 3.3. In Annex 6 of UN/ECE Regulation 101, section 1.4.3 shall be replaced by the following: ‘1.4.3. The fuel consumption, expressed in litres per 100 km (in the case of petrol, LPG, ethanol (E85) and diesel) or in m3 per 100 km (in the case of NG/biomethane) is calculated by means of the following formulae: for vehicles with a positive ignition engine fuelled with petrol (E5): FC = (0,118/D) · [(0,848 · HC) + (0,429 · CO) + (0,273 · CO2)] for vehicles with a positive ignition engine fuelled with LPG: FCnorm = (0,1212/0,538) · [(0,825 · HC) + (0,429 · CO) + (0,273 · CO2)] If the composition of the fuel used for the test differs from the composition that is assumed for the calculation of the normalised consumption, on the manufacturer’s request a correction factor cf may be applied, as follows: FCnorm = (0,1212/0,538) · (cf) · [(0,825 · HC) + (0,429 · CO) + (0,273 · CO2)] The correction factor cf, which may be applied, is determined as follows: cf = 0,825 + 0,0693 nactual where: nactual = the actual H/C ratio of the fuel used for vehicles with a positive ignition engine fuelled with NG/biomethane: FCnorm = (0,1336/0,654) · [(0,749 · HC) + (0,429 · CO) + (0,273 · CO2)] for vehicles with a positive ignition engine fuelled with ethanol (E85): FC = (0,1742/D) · [(0,574 · HC) + (0,429 · CO) + (0,273 · CO2)] for vehicles with a compression ignition engine fuelled with diesel (B5): FC = (0,116/D) · [(0,861 · HC) + (0,429 · CO) + (0,273 · CO2)] In these formulae: FC | = | the fuel consumption in litre per 100 km (in the case of petrol, ethanol, LPG diesel or biodiesel) or in m3 per 100 km (in the case of natural gas) HC | = | the measured emission of hydrocarbons in g/km CO | = | the measured emission of carbon monoxide in g/km CO2 | = | the measured emission of carbon dioxide in g/km D | = | the density of the test fuel. In the case of gaseous fuels this is the density at 15 °C.’ 3.4. In Annex 8 of UN/ECE Regulation 101, references to Annex 4 shall be understood as reference to Appendix 4 of Annex I of this Regulation.
← doc__table__21 · All articles · DETERMINATION OF CO2 EMISSIONS AND FUEL CONSUMPTION →
Source: EUR-Lex (Cellar) · retrieved 2026-11-20 · Text as adopted (Official Journal); later amendments are not incorporated in this text.