Administrative provisions for the type-approval of vehicles with regard to the installation of their tyres

Information document No … relating to the EC type-approval of a vehicle with regard to the installation of its tyres. The following information, if applicable, shall be supplied in triplicate and include a list of contents. Any drawings shall be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4 format. Photographs, if any, shall show sufficient detail. If the systems, components or separate technical units referred to in this information document have electronic controls, information concerning their performance shall be supplied. 0.1. Make (trade name of manufacturer): … 0.2. Type: … 0.2.1. Commercial name(s) (if available): … 0.3. Means of identification of type, if marked on the vehicle If the means of identification of type contains characters not relevant to describe the vehicle, component or separate technical unit types covered by this information document, such characters shall be represented in the documentation by the symbol ‘?’ (e.g. ABC??123??). : … 0.3.1. Location of that marking: … 0.4. Category of vehicle Classified according to the definitions set out in Directive 2007/46/EC Part A of Annex II. : … 0.5. Name and address of manufacturer: … 0.8. Name(s) and address(es) of assembly plant(s): … 0.9. Name and address of the manufacturer’s representative (if any): … 1.1. Photographs and/or drawings of a representative vehicle: … 1.3. Number of axles and wheels: … 1.3.1. Number and position of axles with tyres in dual (twin) formation: … 1.3.2. Number and position of steered axles: … 1.3.3. Powered axles (number, position, interconnection): … 2.3.1. Track of each steered axle Term No 6.5. : … 2.3.2. Track of all other axles Term No 6.5. : … 2.3.3. Width of the widest rear axle: … 2.3.4. Width of the foremost axle (measured at the outermost part of the tyres excluding the bulging of the tyres close to the ground): … 2.8. Technically permissible maximum laden mass stated by the manufacturer For trailers or semi-trailers, and for vehicles coupled with a trailer or a semi-trailer, which exert a significant vertical load on the coupling device or the fifth wheel, this load, divided by standard acceleration of gravity, is included in the maximum technically permissible mass. Please fill in here the upper and lower values for each variant. : … 2.9. Technically permissible maximum mass on each axle: … 2.11.5. Vehicle is/is not Delete where not applicable. suitable for towing loads 4.7. Maximum vehicle design speed (in km/h) With respect to motor vehicles, if the vehicle manufacturer permits that certain controller functions are modified (e.g. by means of software, hardware, upgrading, selection, enabling, disabling) before or after the vehicle has been put into service, resulting in the vehicle having an increased maximum speed, the maximum possible speed achievable by means of adjustment of these controller functions is declared. With respect to trailers, the maximum speed as permitted by the vehicle manufacturer is declared. : … for tyres indicate; size designation(s), load-capacity index Please fill in here the upper and lower values for each variant. , speed category symbol Please fill in here the upper and lower values for each variant. , rolling resistance coefficient (measured in accordance with ISO 28580); for wheels indicate rim size(s) and off-set(s). 6.6.1.1.1. Axle 1: … 6.6.1.1.2. Axle 2: … etc. 6.6.3. Tyre pressure(s) as recommended by the vehicle manufacturer (kPa): … 6.6.4. Description of the snow traction device(s) and the tyre/wheel combination(s) on the front and/or rear axle(s) suitable for the type of vehicle, as recommended by the manufacturer: … 6.6.5. Brief description of temporary-use spare unit (if any): … 6.6.6. Brief description of tyre pressure monitoring system (TPMS) (if fitted): … 9.16.1. Brief description of the vehicle with regard to its wheel guards: … 12.6.1. Manufacturer(s): … 12.6.2. Type(s): … 12.6.3. Type-approval number(s), if available: … 12.6.4. Speed or range of speeds at which the speed limitation may be set: … km/h Stamp of type-approval authority Communication concerning: Delete where not applicable. EC type-approval extension of EC type-approval refusal of EC type-approval withdrawal of EC type-approval of a type of vehicle with regard to the installation of its tyres with regard to Regulation (EU) No …/2011 EC type-approval number: … Reason for extension: … 0.1. Make (trade name of manufacturer): … 0.2. Type: … 0.2.1. Commercial name(s) (if available): … 0.3. Means of identification of type, if marked on the vehicle If the means of identification of type contains characters not relevant to describe the vehicle, component or separate technical unit types covered by this information document, such characters shall be represented in the documentation by the symbol ‘?’ (e.g. ABC??123??). : … 0.3.1. Location of that marking: … 0.4. Category of vehicle As defined in Directive 2007/46/EC, Annex II, Section A. : … 0.5. Name and address of manufacturer: … 0.8. Name(s) and address(es) of assembly plant(s): … 0.9. Name and address of the manufacturer’s representative (if any): … 1. Additional information: see Addendum. 2. Technical service responsible for carrying out the tests: … 3. Date of test report: … 4. Number of test report: … 5. Remarks (if any): see Addendum. 6. Place: … 7. Date: … 8. Signature: … Attachments: Information package. Test report

← ANNEX I · All articles · PART 1 →

Source: EUR-Lex (Cellar) · retrieved 2026-11-06 · Text as adopted (Official Journal); later amendments are not incorporated in this text.