lexiara

ANNEX II

The design characteristics of the vehicle type shall permit entry to and exit from the passenger compartment in complete safety and entrances to the passenger compartment shall be constructed in such a way that they can be used easily and without any danger. The wheel hub, rims and other parts of the wheel shall not be deemed to be running boards or access steps for the purpose of this Regulation, except where reasons relating to construction or use preclude the fitting of running boards or access steps elsewhere on the vehicle. The height of the floor entrance is determined either directly from the ground surface or from the horizontal plane passing through the middle, in relation to the longitudinal direction, of the step immediately below. The distance (A) from the ground surface to the upper surface of the lowest step, measured with the vehicle in running order on a horizontal and flat surface, shall not be more than 600 mm. However, for off-road vehicles (ORV) the distance (A) may be increased up to 700 mm. The distance (B) between the upper surfaces of the steps shall be not more than 400 mm. The vertical distance between two subsequent steps shall not vary by more than 50 mm. The last requirement shall not apply to the distance between the uppermost step and the floor entrance of the passenger compartment. However, for off-road vehicles (ORV) the allowed variation as indicated above may be increased up to 100 mm. In addition, the following minimum geometrical specifications shall be fulfilled: step depth (D): 80 mm; step clearance (E) (include step depth): 150 mm; step width (F): 300 mm; width of the lowest step (G): 200 mm; step height (S): 120 mm; transversal offset between steps (H): 0 mm; longitudinal overlap (J) between two subsequent steps in the same flight, or between the uppermost step and the cab floor entrance height: 200 mm. However, for off-road vehicles (ORV) the value (F) may be reduced to 200 mm. In the case of off-road vehicles (ORV), the lowest step may be designed as a rung if this is necessary for reasons relating to construction or use. In such a case the rung depth (R) shall be at least 20 mm. Rungs with a round cross-section are not permitted. While getting down from the passenger compartment, the position of the uppermost step shall be easily found out. All access steps shall be constructed in such a way as to preclude the risk of slipping. In addition, access steps exposed to the weather and dirt during driving shall have adequate run-off or a draining surface. One or more suitable handrail(s), handhold(s) or other equivalent holding device(s) shall be provided for the access to the passenger compartment. All handrails, handholds or equivalent holding devices shall be positioned in such a way that they can easily be grasped and do not obstruct access to the passenger compartment. A maximum discontinuity of 100 mm in the handhold area of the handrails, handholds or equivalent holding devices may be allowed. In the case of passenger compartment access with more than two steps, the handrails, handholds or equivalent holding devices shall be located in such a way that a person can support himself at the same time with two hands and one foot or with two feet and one hand. Except in the case of a stairway, the design and positioning of the handrails, handholds and equivalent holding devices shall be such that operators are encouraged to descend facing the passenger compartment. The steering wheel may be considered as a handhold. The height (N) of the lower edge of at least one handrail, handhold or equivalent holding device, measured from the ground surface with the vehicle in running order on a horizontal and flat surface, shall not exceed 1850 mm. However, for off-road vehicles (ORV) the distance (N) may be increased up to 1950 mm. If the floor entrance height of the passenger compartment measured from the ground surface is greater than ‘N’, this height shall be assumed as ‘N’. In addition, the minimum distance (P) of the upper edge of the handrails or handholds or equivalent holding devices from the floor entrance height of the passenger compartment shall be: handrails, handholds or equivalent holding devices (U): 650 mm; handrails, handholds or equivalent holding devices (V): 550 mm. The following geometrical specifications shall be fulfilled: gripping dimension (K): 16 mm minimum 38 mm maximum; length (M): 150 mm minimum; clearance to vehicle components (L): 40 mm minimum with open door. middle of the step immediately below the passenger compartment floor entrance (paragraph 1.4. lowest step, rung in case of ORV) Vehicles of categories M_(1) and N_(1) as well as N_(2) with a maximum mass not exceeding 7,5 tonnes, shall have one or more running board(s) or access step(s) if the floor entrance height of the passenger compartment is higher than 600 mm above the ground measured with the vehicle in running order on a horizontal and flat surface. However, for off-road vehicles (ORV), the distance specified above may be increased up to 700 mm. All running boards and access steps shall be constructed in such a way as to preclude the risk of slipping. In addition, running boards and access steps exposed to the weather and dirt during driving shall have adequate run-off or a draining surface.

· All articles ·

Source: EUR-Lex (Cellar) · retrieved 2026-11-20 · Text as adopted (Official Journal); later amendments are not incorporated in this text.