PART IV

Weapons of mass destruction-related items, materials, equipment, goods and technology identified and designated pursuant to paragraph 25 of UN Security Council Resolution 2270 (2016). The nomenclature codes are taken from the Combined Nomenclature as defined in Article 1(2) of Council Regulation (EEC) No 2658/87 of 23 July 1987 on the tariff and statistical nomenclature and on the Common Customs Tariff and as set out in Annex I thereto, which are valid at the time of publication of this Regulation and mutatis mutandis as amended by subsequent legislation. Permanent magnet materials having both the following characteristics: Ring-shaped magnet with a relation between outer and inner diameter smaller or equal to 1.6:1; and Made of any of the following magnetic materials: aluminium-nickel-cobalt, ferrites, samarium-cobalt, or neodymium-iron-boron. ex85051100 ex85051910 ex85051990 ex85059090 Maraging steel having both the following characteristics: ‘capable of’ an ultimate tensile strength of 1500 MPa or more at 293 K (20 °C). In bar or tube form, with an outer diameter of 75 mm or greater. ex73044910 ex73045181 ex73045189 ex73045992 ex73045993 ex73045999 (3) Magnetic alloy materials in sheet or thin strip form having both of the following characteristics: Thickness of 0,05 mm or less; or height of 25 mm or less, and Made of any of the following magnetic alloy materials: iron-chromium-cobalt, iron-cobalt-vanadium, iron-chromium-cobalt-vanadium, or iron-chromium. ex73261910 ex73261990 ex73269092 ex73269094 ex73269096 ex73269098 Frequency changers, other than those specified in entries 0B001.b.13 or 3A225 of Annex II, having all of the following characteristics, and specially designed software therefore: Multiphase frequency output; Capable of providing a power of 40 W or greater; and Capable of operating anywhere (at any one point or more) within the frequency range of between 600 and 2000 Hz. Technical Notes: Frequency changers are also known as converters or inverters. The functionality specified above may be met by certain equipment described or marketed as electronic test equipment, AC power supplies, variable speed motor drives, or variable frequency drives. ex85044084 ex85044088 ex85044090 ex85371095 ex85371098 ex85372091 ex85372099 Aluminium alloys having both the following characteristics: ‘capable of’ an ultimate tensile of strength of 415 MPa or more at 293 K (20 °C) and In bar or tube form, with an outer diameter of 75 mm or greater. Technical Note: The phrase ‘capable of’ encompasses aluminium alloy before or after heat treatment. ex76012080 ex76042910 ex76082020 ex76082081 ex76082089 ‘Fibrous or filamentary materials’ and prepregs, as follows: Carbon, aramid, or glass ‘fibrous or filamentary materials’ having both of the following characteristics: A ‘specific modulus’ exceeding 3,18 × 10^(6) m; and A ‘specific tensile strength’ exceeding 76,2 × 10^(3) m; Prepregs: Thermoset resin-impregnated continuous ‘yarns’, ‘rovings’, ‘tows’ or ‘tapes’ with a width of 30 mm or less, made from carbon, aramid, or glass ‘fibrous or filamentary materials’ controlled in (a) above. ex54021100 ex54021900 ex54023100 ex54023200 ex54049090 ex54071000 ex54072090 ex54074100 ex54074200 ex54074300 ex54074400 ex55011000 ex55019000 ex55031100 ex55031900 ex55032000 ex55039000 ex55061000 ex55069000 ex55091100 ex55091200 ex56049010 ex56075011 ex56075019 ex56075030 ex56075090 ex56090000 ex59021010 ex59021090 ex59022090 ex59029010 ex59029090 ex59031010 ex59031090 ex59032010 ex59032090 ex59039010 ex59039091 ex59039099 ex68151010 ex68159900 ex70191200 ex70191910 ex70191990 ex70195100 ex70195900 ex70199000 Filament winding machines and related equipment, as follows: Filament winding machines having all of the following characteristics: Having motions for positioning, wrapping, and winding fibres coordinated and programmed in two or more axes; Specially designed to fabricate composite structures or laminates from ‘fibrous or filamentary materials’; and Capable of winding cylindrical tubes of diameter of 75 mm or greater; Coordinating and programming controls for filament winding machines specified in (a) above; Mandrels for filament winding machines specified in (a) above. ex84198930 ex84198998 ex84199085 ex84440010 ex84440090 ex84461000 ex84462100 ex84462900 ex84463000 ex84471100 ex84471200 ex84472020 ex84472080 ex84479000 ex84481900 ex84482000 ex84483900 ex84484200 ex84484900 ex84485900 ex84798997 ex84799020 ex84799070 ex85371010 ex85371091 ex85371095 ex85371098 ex85381000 ex90221200 ex90221900 ex90229000 ex90318080 ex90319000 As described in INFCIRC/254/Rev.9/Part2 and S/2014/253 ex84639000 ex84669400 ex85158010 ex85158090 ex85159000 ex84571010 ex84571090 ex84572000 ex84573010 ex84573090 ex84581120 ex84581141 ex84581149 ex84581180 ex84581900 ex84589120 ex84589180 ex84591000 ex84592100 ex84593100 ex84594100 ex84595100 ex84596110 ex84596190 ex84601200 ex84602200 ex84602300 ex84602400 ex84603100 ex84604010 ex84609000 ex84612000 ex84613010 ex84614011 ex84614031 ex84614071 ex84614090 ex84619000 ex84642011 ex84642019 ex84642080 ex84649000 ex85564000 ex85153100 ex85153990 ex85158010 ex85158090 ex85159000 ex28500020 Additional chemicals suitable for the production of chemical warfare agents: Product description CN code Sodium metal (7440-23-5) 28051100 Sulphur trioxide (7446-11-9) ex 28112910 Aluminium chloride (7446-70-0) 28273200 Potassium Bromide (7758-02-3) 28275100 Sodium bromide (7647-15-6) 28275100 Dichloromethane (75-09-2) 29031200 Isopropyl bromide (75-26-3) ex 29033919 Isopropyl ether (108-20-3) ex 29091990 Monoisopropylamine (75-31-0) ex 29211999 Trimethylamine (75-50-3) ex 29211100 Tributylamine (102-82-9) ex 29211999 Triethylamine (121-44-8) ex 29211999 N,N-Dimethylaniline (121-69-7) ex 29214200 Pyridine (110-86-1) ex 29333100 Reaction vessels, reactors, agitators, heat exchangers, condensers, pumps, valves, storage tanks, containers, receivers, and distillation or absorption columns that meet performance parameters described in S/2006/853 and S/2006/853/corr.1. Single-seal pumps with manufacturer's specified maximum flow-rate greater than 0,6 m^(3)/h and casings (pump bodies), preformed casing liners, impellers, rotors or jet pump nozzles designed for such pumps, in which all surfaces that come into direct contact with the chemical(s) being processed are made from any of the following materials: nickel or alloys with more than 40 % nickel by weight; alloys with more than 25 % nickel and 20 % chromium by weight; fluoropolymers (polymeric or elastomeric materials with more than 35 % fluorine by weight); glass or glass-lined (including vitrified or enamelled coating); graphite or carbon-graphite; tantalum or tantalum alloys; titanium or titanium alloys; zirconium or zirconium alloys; ceramics; ferrosilicon (high silicon iron alloys); or niobium (columbium) or niobium alloys. ex39251000 ex39259080 ex39269092 ex39269097 ex40092100 ex40092200 ex40094100 ex40094200 ex40169300 ex69091100 ex69091200 ex69091900 ex69099000 ex69149000 ex70200010 ex70200030 ex70200080 ex73044100 ex73044993 ex73044995 ex73044999 ex73045181 ex73045189 ex73045992 ex73045993 ex73045999 ex73064020 ex73064080 ex73065020 ex73065080 ex73066910 ex73066990 ex73069000 ex73090010 ex73090030 ex73090051 ex73090059 ex73090090 ex73101000 ex73102910 ex73102990 ex73110000 ex73269092 ex73269094 ex73269096 ex73269098 ex75071100 ex75071200 ex75072000 ex75089000 ex81039090 ex81089050 ex81089060 ex81089090 ex81099000 ex81129930 ex84012000 ex84014000 ex84011000 ex84129020 ex84135040 ex84136039 ex84136061 ex84136069 ex84136070 ex84136080 ex84137021 ex84137029 ex84137045 ex84137051 ex84137059 ex84137065 ex84137075 ex84137081 ex84137089 ex84138100 ex84138200 ex84139100 ex84141025 ex84141081 ex84141089 ex84144010 ex84144090 ex84145915 ex84145925 ex84145923 ex84145995 ex84148011 ex84189910 ex84148019 ex84148059 ex84148073 ex84148075 ex84148078 ex84148080 ex84149000 ex84178030 ex84178050 ex84178070 ex84186900 ex84194000 ex84195000 ex84198910 ex84198930 ex84198998 ex84199085 ex84778093 ex84778099 ex84798200 ex84798997 ex84799070 Conventional or turbulent air-flow clean-air rooms and self-contained fan-HEPA filter units that could be used for P3 or P4 (BSL 3, BSL 4, L3, L4) containment facilities. ex84145100 ex84145900 ex84146000 ex84148080 ex84213915 ex84213925 ex84798997

← anx_II__cpt_1__cpt_3__table_1__row_9__cell_2 · All articles · anx_II__cpt_1__cpt_4__text_1 →

Source: EUR-Lex (Cellar) · retrieved 2026-11-06 · Text as adopted (Official Journal); later amendments are not incorporated in this text.