ANNEX II

Information document No … relating to the EC type-approval as a separate technical unit of spray suppression systems. The following information shall be supplied in triplicate and include a list of contents. Any drawings shall be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4 format. Photographs, if any, shall show sufficient detail. If the systems, components or separate technical units referred to in this information document have electronic controls, information concerning their performance shall be supplied. 0.1. Make (trade name of manufacturer): … 0.2. Type: … 0.5. Name and address of manufacturer: … 0.7. In the case of components and separate technical units, location and method of affixing of the EC approval mark: … 0.8. Address(es) of assembly plant(s): … 0.9. Name and address of the manufacturer’s representative (if any): … 1.1. A technical description of the spray suppression device indicating its physical operating principle and the relevant test to which it must be subject: … 1.2. The materials used: … 1.3. Drawing(s) in sufficient detail and to an appropriate scale to enable this (or these) to be identified. The drawing must show the space intended for the EC component type-approval mark: … Date Signed Stamp of approval authority Communication concerning: — EC type-approval (1) — extension of EC type-approval (1) — refusal of EC type-approval (1) — withdrawal of EC type-approval (1) | of a type of spray suppression system as a component/separate technical unit with regard to Regulation (EU) No …/…, as last amended by Regulation (EU) No …/… (1) EC type-approval number: … Reason for extension: … 0.1. Make (trade name of manufacturer) … 0.2. Type:… 0.3. Means of identification of type, if marked on the separate technical unit (2): … 0.3.1. Location of that marking: … 0.5. Name and address of manufacturer: … 0.7. Location and method of affixing of the EC approval mark: … 0.8. Name(s) and address(es) of assembly plant(s): … 0.9. Name and address of the manufacturer’s representative (if any): … 1. Additional information (where applicable): see Addendum. 2. Technical service responsible for carrying out the tests: … 3. Date of test report: … 4. Number of test report: … 5. Remarks (if any): see Addendum. 6. Place: … 7. Date: … 8. Signature: … 9. The index to the information package lodged with the approval authority, which may be obtained on request, is attached. 1.1. Operating principle of device: energy-absorption/air/water separator (3): 1.2. Characteristics of spray suppression devices (brief description, trademark or name, number(s): 5. Remarks (if any): 1. The EC separate technical unit type-approval mark shall consist of: 1.1. A rectangle surrounding the lower-case letter ‘e’ followed by the distinguishing number of the Member State which has granted the EC separate technical unit type-approval: for Germany for France for Italy for The Netherlands for Sweden for Belgium for Hungary for the Czech Republic for Spain for the United Kingdom for Austria for Luxembourg for Finland for Denmark for Romania for Poland for Portugal for Greece for Ireland for Slovenia for Slovakia for Estonia for Latvia for Bulgaria for Lithuania for Cyprus for Malta 1.2. In the vicinity of the rectangle the ‘base approval number’ contained in Section 4 of the type-approval number preceded by the two figures indicating the sequence number assigned to this Regulation or latest major technical amendment to this Regulation. The sequence number is ‘00’ at present. 2. The EC separate technical unit type-approval mark shall be affixed to the spray suppression device in such a way as to be indelible as well as clearly and easily legible even if the device is fitted to a vehicle. 3. An example of an EC separate technical unit type-approval mark is shown as follows. Explanatory note The EC separate technical unit type-approval was issued by The Netherlands under number 0046. The first two digits ‘00’ indicate that the separate technical unit was approved according to this Regulation. The symbol ‘A’ indicates it is a device of the energy-absorption type.

← doc__heading__4__para__3 · All articles · ADMINISTRATIVE DOCUMENTS FOR EC TYPE-APPROVAL OF SPRAY SUPPRESSION SYSTEMS AS SEPARATE TECHNICAL UNITS →

Source: EUR-Lex (Cellar) · retrieved 2026-11-12 · Text as adopted (Official Journal); later amendments are not incorporated in this text.