ANNEX V
The verification tolerances defined in this Annex apply only to the verification by Member State authorities of the declared values. They shall not be used by the manufacturer, importer or authorised representative as an allowed tolerance for establishing the values in the technical documentation or in interpreting those values with a view to achieving compliance or for communicating better performance by any means. Where a model is not in conformity with the requirements laid down in the first paragraph of Article 6 of this Regulation, the model and all equivalent models shall be considered not compliant. As part of verifying the compliance of an equipment model with the requirements laid down in this Regulation pursuant to Article 3(2) of Directive 2009/125/EC, for the requirements referred to in this Annex, the authorities of the Member States shall apply the following procedure: The Member State authorities shall verify one single unit of the model. The model shall be considered to comply with the applicable requirements if all the following conditions are met: the values given in the technical documentation pursuant to point 2 of Annex IV to Directive 2009/125/EC (declared values), and, where applicable, the values used to calculate those values, are not more favourable for the manufacturer, importer or authorised representative than the results of the corresponding measurements carried out pursuant to point 2(g) of that Annex; the declared values meet any requirements laid down in this Regulation, and any required product information published by the manufacturer, importer or authorised representative does not contain values that are more favourable for the manufacturer, importer or authorised representative than the declared values; when Member State authorities check the unit of the model the manufacturer, importer or authorised representative has put in place a system that complies with the requirements in the second paragraph of Article 6; when Member State authorities check the unit of the model, it complies with the functional requirements in point 2 of Annex III and with the information requirements in point 3 of Annex III; when Member State authorities test the unit of the model, the determined values (the values of the relevant parameters as measured in testing and the values calculated from those measurements) comply with the respective verification tolerances as set out in Table 1. If the conditions set out in point 2(a), (b), (c) or (d) are not met, the model and all equivalent models shall be considered not to comply with this Regulation. If the condition set out in point 2(e) is not met, the Member State authorities shall select three additional units of the same model for testing. As an alternative, the three additional units selected may be of one or more equivalent models. The model shall be considered to comply with the applicable requirements if, for those three units, the arithmetical mean of the determined values complies with the respective verification tolerances given in Table 1. If the result referred to in point 5 is not achieved, the model and all equivalent models shall be considered not to comply with this Regulation. The Member State authorities shall provide all relevant information to the authorities of the other Member States and to the Commission without delay after a decision is taken on non-compliance of the model pursuant to points 3 or 6, or the second paragraph of this Annex. The Member State authorities shall use the measurement and calculation methods set out in Annex IV. For the requirements referred to in this Annex, Member State authorities shall apply only the verification tolerances set out in Table 1 below and shall use only the procedure described in points 1 to 7 above. For the parameters in Table 1, no other tolerances, such as those set out in harmonised standards or in any other measurement method, shall be applied. Table 1 Verification tolerances Parameters | Verification tolerances Power consumption in off mode | The determined value (*1) shall not exceed the declared value by more than 0,10 W. Power consumption in standby mode | The determined value (*1) shall not exceed the declared value by more than 0,10 W. Power consumption in networked standby | The determined value (*1) shall not exceed the declared value by more than 0,10 W if the declared value is smaller than 1 W and by more than 10 % otherwise. Time needed for the equipment to reach the applicable low power mode or condition | The determined value (*1) shall not exceed the declared value by more than 10 %
← (d) · All articles · VERIFICATION PROCEDURE FOR MARKET SURVEILLANCE PURPOSES →
Source: EUR-Lex (Cellar) · retrieved 2026-11-19 · Text as adopted (Official Journal); later amendments are not incorporated in this text.